View PI2121_4837715.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PI2121
Cool-ORing
TM
Series
8 Volt, 24 Amp Full-Function Active ORing Solution
Description
The Cool-ORing PI2121 is a complete full-function Active ORing solution with a high-speed ORing MOSFET controller and a very low on-state resistance MOSFET designed for use in redundant power system architectures. The PI2121 Cool-ORing solution is offered in an extremely small, thermally enhanced 5mm x 7mm LGA package and can be used in low voltage ( 5Vbus) high side Active ORing applications. The PI2121 enables extremely low power loss with fast dynamic response to fault conditions, critical for high availability systems. A master/slave feature allows the paralleling of PI2121 solutions for high current Active ORing requirements. The PI2121, with its 1.5m internal MOSFET provides very high efficiency and low power loss during steady state operation, while achieving highspeed turn-off of the internal MOSFET during input power source fault conditions that cause reverse current flow. The PI2121 provides an active low fault flag output to the system during excessive forward current, light load, reverse current, overvoltage, under-voltage and over-temperature fault conditions. A temperature sensing function indicates a fault if the maximum junction temperature exceeds 160C. The under-voltage and over-voltage thresholds are programmable via an external resistor divider.
TM
Features
* * * * * * * * * Integrated High Performance 24A, 1.5m MOSFET Very-small, high density fully-optimized solution providing simple PCB layout. Fast Dynamic Response to Power Source failures, with 160ns reverse current turn-off delay time Accurate sensing capability to indicate system fault conditions Programmable under & over-voltage functions Over temperature fault detection Adjustable reverse current blanking timer Master/Slave I/O for paralleling Active low fault flag output
Applications
* * * * * N+1 Redundant Power Systems Servers & High End Computing Telecom Systems High-side Active ORing High current Active ORing ( 5Vbus)
Package Information
* 17-pin 5mm x 7mm Thermally Enhanced LGA Package
Typical Application:
Figure 2: Figure 1: PI2121 High Side Active ORing
Picor Corporation * picorpower.com
PI2121 input current de-rating based on maximum TJ=150C vs. ambient temperature
Rev. 1.0 Page 1 of 21
PI2121
Pin Description
Pin Name D S SP Pin Number 1, 15, 16, 17 2, 3, 4, 5 6 7 8 Description Drain- The Drain of the internal N-channel MOSFET, connect to the output load. Source-The source of the internal N-channel MOSFET, connect to the input power source bus voltage. Positive Sense Input & Clamp: Connect SP pin to the S pin. The polarity of the voltage difference between SP and SN provides an indication of current flow direction through the MOSFET. Fault State Output: This open collector pin pulls low when a fault occurs. Fault logic inputs are VC Under-Voltage, Input Under-Voltage, Input Over-Voltage, Forward Over-Current, light load, reverse current, and Over-Temperature. Leave this pin open if unused. Blanking timer Input-Output: Connect a resistor from BK to GND to set the blanking time for the Reverse Comparator function. To configure in slave mode, connect BK to VC. To configure in master mode with the fastest turn-off response connect BK directly to GND. Slave Input-Output: This pin is used for paralleling multiple PI2121 solutions in high power applications. When the PI2121 is configured as the Master, this pin functions as an output capable of driving up to 10 SL pins of slaved PI2121 devices. It serves as an input when the PI2121 is configured in slave mode. Input Supply Pin: This pin is the supply pin for the control circuitry and gate driver. Connect a 1F capacitor between VC pin and the GND pin. Voltage on this pin is limited to 15.5V by an internal shunt regulator in high auxiliary voltage applications. For high voltage auxiliary supply applications connect a shunt resistor between VC and the auxiliary supply. Ground: This pin is ground for the gate driver and control circuitry. Input Over Voltage Input: The OV pin is used to detect an input source over-voltage condition in ground referenced applications. When the OV pin voltage crosses the OV threshold, the FT pin pulls low indicating a fault condition. The input voltage OV threshold is programmable through an external resistor divider. Connect OV to GND to disable this function. Input Under-Voltage Input: The UV pin is used to detect an input source under-voltage condition in ground referenced applications. When the UV pin voltage drops below the UV threshold, the FT pin pulls low indicating a fault condition. The input voltage UV threshold is programmable through an external resistor divider. Connect UV to VC to disable this function. Negative Sense Input & Clamp- Connect SN to D pin. The polarity of the voltage difference between SP and SN provides an indication of current flow direction through the MOSFET.
FT
BK
SL
9
VC GND
10 11
OV
12
UV
13
SN
14
Package Pin-out
17 Pin LGA (5mm x 7mm) Top view
Picor Corporation * picorpower.com PI2121 Rev. 1.0 Page 2 of 21
Absolute Maximum Ratings
Drain-to-Source Voltage (VDS) Source Current (IS ) Continuous Source Current (IS ) Pulsed (10s) Thermal Resistance RJA(3) VC SP, SN, OV, 8V @ 25C 24A 100A 54C/W -0.3V to 17.3V / 40mA -0.3V to 8.0V / 10mA -0.3V to 17.3V / 10mA -0.3V / 5A peak -65oC to 150oC -40oC to Over Temperature Fault (TFT) 250oC 2kV HBM
SL
UV,BK, FT GND Storage Temperature Operating Junction Temperature Lead Temperature (Soldering, 20 sec) ESD Rating
Electrical Specifications
Unless otherwise specified: -40C < TJ < 125C, VC =12V, CVc = 1uF, CSL = 10pF Parameter VC Supply Operating Supply Range (4) Quiescent Current VC Clamp Voltage VC Clamp Shunt Resistance VC Under-voltage Rising Threshold VC Under-voltage Falling Threshold VC Under-voltage Hysteresis Internal N-Channel MOSFET Drain-to-Source Breakdown Voltage Source Current Continuous Drain Leakage Current Drain-to-Source On Resistance Body Diode Forward Voltage FAULT Under-Voltage Rising Threshold Under-Voltage Falling Threshold Under-Voltage Threshold Hysteresis Under-Voltage Bias Current Over-Voltage Rising Threshold Over-Voltage Falling Threshold VUVR VUVF VUV-HS IUV VOVR VOVF 440 -1 500 475 440 500 475 25 1 540 540 mV mV mV A mV mV BVDSS IS IDLK RDSon Vf-BD 1.5 0.7 8 24 10 2.0 1.0 V A A m V In OFF state, ID=250A , Tj=25C; Figure 10, page 11 In ON state, Tj=25C In OFF state, VDS=8V, Tj=25C In ON state, IS=20A, Tj=25C VC-V(S) 5V In ON state, IS=4A, Tj=25C VVC-GND IVC VVC-CLM RVC VVCUVR VVCUVF VVCUV-HS 4.0 4.3 4.15 150 15 4.5 3.7 15.5 13.2 4.2 16 7.5 4.5 V mA V V V mV No VC limiting resistors Normal Operating Condition, No Faults IVC=10mA Delta IVC=10mA Symbol Min Typ Max Units Conditions
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 3 of 21
Electrical Specifications
Unless otherwise specified: -40C < TJ < 125C, VC =12V, CVc = 1uF, CSL = 10pF Parameter Symbol Min Typ Max Units FAULT (Continued) Over-Voltage Threshold Hysteresis Over-Voltage Bias Current Fault Output Low Voltage Fault Output High Leakage Current Fault Delay Time Over Temperature Fault (1) Over Temperature Fault Hysteresis(1) Common Mode Input Voltage Differential Operating Input Voltage SP Input Bias Current SN Input Bias Current SN Voltage Reverse Comparator Threshold Reverse Comparator Hysteresis Reverse to Slave Low Delay Time Reverse to Slave Low Delay Time Forward Comparator Threshold Forward Comparator Hysteresis Forward Over Current Comparator Threshold Forward Over Current Comparator Hysteresis SLAVE Slave Source Current Slave Output Voltage High Slave Output Voltage Low Slave Hold-off Voltage at VC UVLO Slave Threshold Slave Fall Time Slave Low to FET Turn Off Delay Time Master Mode Slave Low to FET Turn Off Delay (1) Time Slave Mode
(1)
Conditions
VOV-HS IOV VFTL IFT-LC tFT-DEL TFT TFT-HS VCM VSP-SN ISP ISN VSN VRVS-TH VRVS-HS tRVS-MS tRVS-SL VFWD-TH VFWD-HS VOC-TH VOC-HS 2 -5 60 -8 -10 2 -0.1 -50 -50 20 -1
25 1 0.2 40 160 -10 5.5 125 -37 3.5 -6 8 5.5 -2 5 160 430 6 200 600 9 -2 66 70 -4 0.5 10 60
mV A V A s C C V mV A A V mV mV ns ns mV mV mV mV SP to GND & SN to GND SP-SN SP=SN=1.25V SP=SN=1.25V SP=0V VCM = 3.3V VCM = 3.3V VSP-SN = -50mV step, VBK=0 (minimum blanking) VSP-SN = -50mV step, VBK= VVC (maximum blanking) VCM = 3.3V VCM = 3.3V VCM = 3.3V VCM = 3.3V VSL = 1V, Normal Operating Conditions, No Faults Normal Operating Conditions, No Faults ISL=4mA ISL=5A,1.5V3.5V VFT=14V Includes output glitch filter
DIFFERENTIAL AMPLIFIER AND COMPARATORS
ISL VSL-Hi VSL-Lo VSL-UV VSL-TH tSL-FL tG-SL tG-SL
-60 4.3 0.2 0.7 1.75 15 20 100
-25 5.5 0.5 1 2 25 30 130
A V V V V ns ns ns
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 4 of 21
Electrical Specifications
Unless otherwise specified: -40C < TJ < 125C, VC =12V, CVc = 1uF, CSL = 10pF Parameter Symbol Min Typ Max Units BLANK Blank Source Current Blank Output Voltage Blank Slave Mode Threshold IBK VBK VBK-TH 1.2 -60 -45 0.77 1.45 -30 0.9 1.7 A V V VBK=0V IBK=5A Connected to GND Conditions
Note 1: These parameters are not production tested but are guaranteed by design, characterization and correlation with statistical process control. Note 2: Current sourced by a pin is reported with a negative sign. Note 3: Thermal resistance characterized on PI2121-EVAL1 evaluation board with 0 LFM airflow. Note 4: Refer to the Auxiliary Power Supply section in the Application Information for details on the VC requirement to fully enhance the internal MOSFET.
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 5 of 21
Functional Description: The PI2121 integrated Cool-ORing product takes advantage of two different technologies combining a 1.5m on-state resistance (Rds(on)) single Nchannel MOSFET with high density control circuitry. This combination provides superior density, minimizing PCB space to achieve an ideal ORing diode function, significantly reducing power dissipation and eliminating the need for heat sinking, while minimizing design complexity. The PI2121's 1.5m on-state resistance MOSFET used in the conduction path enables a dramatic reduction in power dissipation versus the performance of a diode used in conventional ORing applications due to its high forward voltage drop. This can allow for the elimination of complex heat sinking and other thermal management requirements. Due to the inherent characteristics of the integrated MOSFET, while the gate remains enhanced above the gate threshold voltage it will allow current to flow in the forward and reverse direction. Ideal ORing applications do not allow for reverse current flow, so the integrated controller has to be capable of very fast and accurate detection of reverse current caused by input power source failures, and turn off the gate of the MOSFET as quickly as possible. Once the gate voltage falls below the gate threshold, the MOSFET is off and the body diode will be reverse biased preventing reverse current flow and subsequent excessive voltage droop on the redundant bus. During forward overcurrent conditions caused by load faults, the controller maintains gate drive to the MOSFET to keep power dissipation as low as possible, otherwise the inherent body diode of the MOSFET would conduct, which has higher effective forward drop. Conventional ORing solutions using diodes offer no protection against forward over-current conditions. During the forward over-current condition, the PI2121 will provide an active-low fault flag to the system via the fault pin. The fault flag is also issued during the reverse current condition, light load conditions, VC under-voltage, Input UnderVoltage and Over-Voltage and Over-Temperature conditions. Differential Amplifier: The PI2121 integrates a high-speed, low offset voltage differential amplifier to sense the difference between the Sense Positive (SP) pin voltage and Sense Negative (SN) pin voltage with high accuracy. The amplifier output is connected to three comparators: Reverse comparator, Forward comparator, and Forward over-current comparator. Reverse Comparator: RVS The reverse comparator is the most critical comparator. It looks for negative voltage caused by reverse current. When the SN pin is 6mV higher than the SP pin, the reverse comparator will enable the BK current source to charge an internal 2pF capacitor. The blanking timer provides noise filtering for typical switching power conversion that might cause premature reverse current detection. Once the voltage across the capacitor reaches the timer threshold voltage (1.25V) the MOSFET will be turned off. The shortest blanking time is 50ns when BK is connected to ground. The Blanking time will be added to the controller delay time. The Electrical Specifications in the DIFFERENTIAL AMPLIFIER AND COMPARATOR section for Reverse Fault to Slave Low Delay Time "tRVS-MS or tRVS-SL" is the controller delay time plus the blanking time. Reverse Blanking Timer: BK Connecting an external resistor ( RBK ) between the BK pin and ground will increase the blanking time as shown in the following chart. Where: RBK 200 K If BK is connected to VC for slave mode operation, then the blanking time will be about 320ns typically, and total delay time will be 430ns. The reverse comparator has 3mV of hysteresis referenced to SP-SN. If the conditions are met for a reverse current fault, then the active-low fault flag output will also indicate a fault to the system after the 40s fault delay time.
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 6 of 21
Forward Voltage Comparator: FWD The FWD comparator detects when a forward current condition exists and SP is 6mV positive with respect to SN. When SP-SN is less than 6mV, the FWD comparator will assert the Fault flag to report a fault condition indicative of a light load "load not present" condition or possible shorted MOSFET. Forward Over Current Comparator: FOC The FOC comparator indicates an excessive forward current condition when SP is 66mV (typical) higher than SN. When the FET is in the on-state and SPSN is higher than 66mV (typical) the PI2121 will initiate a fault condition via the FT pin. Slave: In high current applications that exceed the single PI2121 current handling capability, multiple PI2121's can be paralleled and synchronized by using the slave function. The Slave function synchronizes multiple PI2121's together and allows for localized control of each paralleled MOSFET. One PI2121 will be designated as the master and it will control the response of the slaved PI2121's. When the PI2121 is configured in the "Master Mode" by connecting the BK to ground, the SL will be an output having the same signal characteristics as the internal Gate Driver. In this configuration, the SL output is capable of driving up to ten PI2121's, configured in "Slave Mode", through their corresponding SL pins. Logic high for the SL pin is limited to 5.5V (max). When the BK pin is tied to VC, the PI2121 becomes a slave and the SL pin will be an input. The internal Gate driver section and reverse current section are the only active circuits in the slaved PI2121 while the master performs the diagnostics and gate drive control. VC and Internal Voltage Regulator: The PI2121 has a separate input (VC) that provides power to the control circuitry and the internal gate driver. An internal regulator clamps the VC voltage to 15.5V. For high side applications, the VC input should be 5V above the bus voltage to properly enhance the internal N-channel MOSFET. The internal regulator circuit has a comparator to monitor the VC voltage and initiates a FAULT
Picor Corporation * picorpower.com
condition when VC is lower than the VC UnderVoltage Threshold UV: The Under-Voltage (UV) input trip point can be programmed through an external resistor divider to monitor the input voltage. The UV comparator initiates a fault condition and pulls the FT pin low, when UV falls below the Under-Voltage Falling Threshold. If the PI2121 is configured in a floating application, where the GND pin is connected to the input voltage, the UV pin cannot detect the input voltage. In this case, the UV pin should be disabled by connecting it to the VC pin. OV: The Over-Voltage (OV) input trip point can be programmed through an external resistor divider to monitor the input voltage. The OV comparator initiates a fault condition and pulls the FT pin low when OV rises above the Over-Voltage Rising Threshold. If the PI2121 is configured in a floating application, where the GND pin is connected to the input voltage, the OV pin cannot detect the input voltage. In this case, the OV pin should be disabled by connecting it to the controller GND pin. Over-Temperature Detection: The internal Over-Temperature block monitors the junction temperature of the controller. The overtemperature threshold is set to 160C with -10C of hysteresis. When the controller temperature exceeds this threshold, the over-temperature circuit initiates a fault condition and pulls the FT pin low. Fault: The fault circuit output is an open collector with 40s delay to prevent any false triggering. The FT pin will be pulled low when any of the following faults occur: * Reverse Current * Forward Over-Current * Forward Low Current * Over-Temperature * Input Under-Voltage * Input Over-Voltage * VC pin Under-Voltage A gate voltage detector prevents FOC or FWD from initiating a fault when the MOSFET is in an OFF condition. The only fault condition that initiates gate turn-off of the MOSFET (as well as a fault flag signal) is when the reverse current fault conditions are met. All other fault conditions issue only a fault flag signal via the
PI2121 Rev. 1.0 Page 7 of 21
condition may be present. This information can be
FT pin, but do not affect the gate of the MOSFET. The FT pin serves as an indicator that a fault
reported to a Host to signal that some system level maintenance may be required.
Figure 3: PI2121 Internal Block Diagram
Figure 4: Comparator hysteresis, values are for reference only, please refer to the electrical specifications.
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 8 of 21
Figure 5: Timing diagram for two PI2121 solutions in an Active ORing application
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 9 of 21
Figure 6: PI2121 State diagram, master mode.
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 10 of 21
Typical Characteristics:
Figure 7: Reverse Condition internal MOSFET Turn off delay time vs. temperature.
Figure 8: Reverse comparator threshold vs. temperature. VCM: Common Mode Voltage.
Figure 9: Controller bias current vs. temperature.
Figure 10: Internal MOSFET drain to source breakdown voltage vs. temperature.
Figure 11: Internal MOSFET on-state resistance vs. temperature.
Picor Corporation * picorpower.com
Figure 12: Internal MOSFET source to drain diode forward voltage (pulsed 300s).
PI2121 Rev. 1.0 Page 11 of 21
Thermal Characteristics:
Figure 13: Junction Temperature vs. Input Current (0LFM)
Figure 14: Junction Temperature vs. Input Current (200LFM)
Figure 15: PI2121 mounted on PI2121-EVAL1 Thermal Image picture, Iout=24A, TA=25C, Air Flow=0LFM
Figure 16: PI2121 mounted on PI2121-EVAL1 Thermal Image picture, Iout=24A, TA=25C, Air Flow=200LFM
Figure 17: PI2121 input current de-rating based on maximum TJ=150C vs. ambient temperature
Picor Corporation * picorpower.com PI2121 Rev. 1.0 Page 12 of 21
Figure 18: Plot of PI2121 response time to reverse current detection (Example 1, Figure 22)
Application Information
The PI2121 is designed to replace ORing diodes in high current, low voltage redundant power architectures. Replacing a traditional diode with a PI2121 will result in significant power dissipation reduction as well as board space reduction, efficiency improvement and additional protection features. This section describes in detail the procedure to follow when designing with the PI2121 Active ORing solution. Two Active ORing design examples are presented. Fault Indication: The FT output pin is an open collector and should be pulled up to the logic voltage or to the controller VC via a resistor (10K). Blanking Timer: Connect the blanking timer pin (BK) to GND to program the device for the fastest reverse comparator response time of 160ns typical. To increase the blanking time, connect the BK pin to GND via a resistor to avoid the fault response to short reverse current pulses. Refer to the plot in the reverse comparator functional description for resistor values versus the reverse blanking time. Auxiliary Power Supply (Vaux): Vaux is an independent power source required to supply power to the VC input. The Vaux voltage should be 5V higher than Vin (redundant power source output voltage) to fully enhance the internal MOSFET.
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 13 of 21
A bias resistor (Rbias) is required if Vaux is higher than 15V. Rbias should be connected between the VC pin and Vaux. Minimize the resistor value for low Vaux voltage levels to avoid a voltage drop that may reduce the VC voltage lower than required to drive the gate of the internal MOSFET. Select the value of Rbias using the following equations:
Rbias =
Vaux min - VC clamp IC max
source. At the same time the energy stored at the drain side of the internal MOSFET will be released and produce a voltage higher than the load voltage. This event will create a high voltage difference between the drain and source of the MOSFET. To reduce the magnitude of the ringing voltage, add a ceramic capacitor very close to the source that can react to the voltage ringing frequency and another capacitor close to the drain. Recommended values for the ceramic capacitors are 1F, refer to C5 and C7 in Figure 24. Slave: For a high current application where one PI2121 can not handle the total load current, multiple PI2121's can be paralleled in a master / slave configuration to support the total current per input. In the Master / Slave mode, one PI2121 is configured as the master and the rest are configured as slaves. The slave ( SL ) pin of the master unit will act as an output driving the units configured in slave mode. The SL pins of the slave units will act as inputs under the control of the master. Tie the BK pin to VC to configure the unit in slave mode. Power dissipation: In Active ORing circuits the MOSFET is always on in steady state operation and the power dissipation is derived from the total source current and the onstate resistance of the internal MOSFET. The PI2121 internal MOSFET power dissipation can be calculated with the following equation:
Rbias maximum power dissipation:
Pd Rbias =
Where:
(Vauxmax - VC clamp ) 2 Rbias
Vauxmin : Vaux minimum voltage Vauxmax : Vaux maximum voltage VC Clamp : Controller clamp voltage, 15.5V
IC max
: Controller maximum bias current, use 4.2mA Example: Vaux 20V to 30V
Rbias =
Vauxmin - VC clamp IC max
=
20V - 15.5V = 1.07 K 4.2mA
Pd Rbias =
(Vauxmax - VC clamp ) 2 Rbias
=
(30V - 15.5V ) 2 = 196mW 1.07 K
Internal N-Channel MOSFET BVdss: The PI2121's internal N-Channel MOSFET breakdown voltage (BVdss) is rated for 8V at 25C and will degrade at -40C to 7.75V, refer to Figure 10. In an application when the MOSFET is turned off due to a reverse fault, the series parasitic elements in the circuit may contribute to the MOSFET being exposed to a voltage higher than its voltage rating. In Active ORing applications when one of the input power sources is shorted, a large reverse current is sourced from the circuit output through the MOSFET. Depending on the output impedance of the system, the reverse current may reach over 60A in some conditions before the MOSFET is turned off. Such high current conditions will store energy even in a small parasitic element. For example: a 1nH parasitic inductance with 60A reverse current will generate 1.8J (1/2Li2). When the MOSFET is turned off, the stored energy will be released and produce a high negative voltage ringing at the MOSFET
Picor Corporation * picorpower.com
Pd MOSFET = Is 2 Rds(on)
Where: Is : Source Current Rds(on) : MOSFET on-state resistance Note: Calculate with Rds(on) at maximum MOSFET temperature because Rds(on) is temperature dependent. Refer to figure 11 for normalized Rds(on) values over temperature. PI2121 nominal Rds(on) at 25C is 1.5m and will increase by 40% at 125C junction temperature. The Junction Temperature rise is a function of power dissipation and thermal resistance.
Trise= RthJA PdMOSFET = RthJA Is 2 Rds(on) ,
Where: RthJA : Junction-to-Ambient thermal resistance (54C/Watt)(3)
PI2121
Rev. 1.0
Page 14 of 21
Where: This may require iteration to get to the final junction temperature. Figures 13, 14, and 17 show the PI2121 internal MOSFET final junction temperature curves versus conducted current at given ambient temperatures and air flow. OV/UV resistor selection: The UV and OV comparator inputs are used to monitor the input voltage and will indicate a fault condition when this voltage is out of range. The UV & OV pins can be configured in two different ways, either with a divider on each pin, or with a threeresistor divider to the same node, enabling the elimination of one resistor. Under-voltage is monitored by the UV pin input and over-voltage is monitored with the OV pin input. The Fault pin ( FT ) will indicate a fault (active low) when the UV pin is below the threshold or when the OV pin is above the threshold. The threshold is 0.50V typical with 25mV hysteresis and the input current is less than 1A. It is important to consider the maximum current that will flow in the resistor divider and maximum error due to UV and OV input current. Set the resistor current to 100A or higher to maintain better than 1% accuracy for UV and OV due to the bias current. The three-resistor voltage divider configuration for both UV and OV to monitor the same voltage node is shown in Figure 19:
V (UVTH ) V (OVTH ) V (UV ) I Ra
: UV threshold voltage at Vin. : OV threshold voltage at Vin. : UV voltage set : Ra current.
Alternatively, a two-resistor voltage divider configuration can be used and is shown in (Figure 20). The UV resistor voltage divider can be obtained from the following equations:
R1UV =
V (UVTH ) I RUV
Set R1UV value based on system allowable current
I RUV 100A
V (UV ) R 2 UV = R1UV V (UV ) - 1 TH
Where:
V (UVTH ) : UV threshold voltage : R1UV current I RUV
R1UV =
V (UVTH ) I RUV
Set R1OV value based on system allowable current
I RUV 100A
V (OV ) R 2 OV = R1OV V (OV ) - 1 TH
Where:
V (OVTH ) : OV threshold voltage : R1OV current I ROV
Figure 19: UV & OV three-resistor divider configuration
Ra =
Set
V (OVTH ) I Ra
Ra value based on system allowable current
Figure 20: UV & OV two-resistor divider configuration
I Ra
V (OV ) Rb = Ra V (UV ) - 1
V (UV ) Rc = (Ra + Rb ) V (UV ) - 1 TH
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 15 of 21
Typical Application Example 1: Requirement: Redundant Bus Voltage = 3.3V Load Current = 20A (assume through each redundant path) Maximum Ambient Temperature = 60C, no air flow Auxiliary Voltage = 12V (10V to 14V) Solution: A single PI2121 for each redundant 3.3V power source should be used, configured as shown in the circuit schematic in Figure 22. Vaux: Since the Vaux voltage does not exceed the VC pin clamp voltage, connect the Vaux directly to the VC pin SP and SN pins: Connect each SP pin to the S pins and each SN pin to the D pins BK pin: Connect the BK pin to ground to achieve the minimum reverse current response time. Rds(on) is 2.0m maximum at 25C and will increase as the Junction temperature increases. From Figure 11, at 118C Rds(on) will increase by ~35%, then
Rds(on) = 2.0m 1.35 = 2.7m maximum at 118C
Maximum power dissipation is:
Pdmax = Iin2 Rds(on) = (20A)2 2.7m = 1.08W
Recalculate TJ:
54C TJ max = 60C + (20A)2 2.7m = 118.3C W
SL pin: Not required, so leave floating
FT pin: Connect to the logic input and to the logic power supply via a 10K resistor.
Program UV and OV to monitor input voltage: Program UV at 3.0V and OV at 3.6V Use the three-resistor divider configuration: Figure 21: Example 1 final junction temperature at 20A/60C TA Reverse Current Threshold: The following procedure demonstrates how to calculate the minimum required reverse current in the internal MOSFET to generate a reverse fault condition and turn off the internal MOSFET. At room temperature (25C) typical Rds(on):
I Ra = 200A 500mV Ra = = 2.5k or 2.49k 1% 200A 3.6V Rb = 2.49k - 1 = 498 or 499 1% 3.0V 3.0V - 1 = 14.95k Rc = (2.49k + 499 ) 500mV
or 15k 1%
Is.reverse =
Vth.reverse - 6mV = = -4 A Rds(on) 1.5m
Power Dissipation and Junction Temperature: First use Figure 13 (Junction Temperature vs. Input Current) to find the final junction temperature for 20A load current at 60C ambient temperature. In Figure 13 (illustrated in Figure 21) draw a vertical line from 20A to intersect the 60C ambient temperature line. At the intersection draw a horizontal line towards the Y-axis (Junction Temperature). The Junction Temperature at full load current (20A) and 60C ambient is 118C.
Picor Corporation * picorpower.com
At maximum junction temperature (118C) and maximum Rds(on):
Is.reverse =
Vth.reverse - 6mV = = -2.2 A Rds(on) 2.7 m
PI2121
Rev. 1.0
Page 16 of 21
Typical Application Example 2: Requirement: Redundant Bus Voltage = 1.2V Load Current = 100A (assume through each redundant path) Auxiliary Voltage = 12V Solution: Five PI2121's for each redundant 1.2V power source should be used, configured in a master / slave configuration as shown in the circuit schematic in Figure 23. Vaux: Since the Vaux voltage does not exceed the VC pin clamp voltage, connect the Vaux directly to each PI2121 VC pin. SP and SN pins: For each specific PI2121, connect each SP pin to the respective S pins and each SN pin to the respective D pins. The master unit will perform the sensing function. BK pin: Connect the Master PI2121 BK pin directly to ground to achieve the minimum reverse current response time, and connect the BK pin of the slaved PI2121's to the respective local VC pin.
Figure 22: Two PI2121 in High Side ORing configuration
SL pin: For each set of parallel PI2121's connect the SL pins together.
FT pin: Connect the FT pin of the Master PI2121 to a logic input and to the logic power supply via a 10K resistor.
Program UV and OV of the Master PI2121 to monitor Input Voltage: Program UV at 1.1V and OV at 1.3V Use the three-resistor divider configuration:
I Ra = 200A 500mV Ra = = 2.5k or 2.49k 1% 200A 1.3V Rb = 2.49k - 1 = 452 or 453 1% 1.1V 1.1V - 1 = 3.53.k Rc = (2.49 k + 453 ) 500mV
or 3.57k 1%
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 17 of 21
Figure 23: PI2121 used in a 100A Active ORing application (master/slave configuration)
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 18 of 21
Layout Recommendation:
Use the following general guidelines when designing printed circuit boards. An example of the typical land pattern for the PI2121 is shown in Figure 24: * * Make sure to have a solid ground (return) plane to reduce circuit parasitic. Connect all S pads together with a wide trace to reduce trace parasitics to accommodate the high current input, and also connect all D pads together with a wide trace to accommodate the high current output. Connect the SP pin to the S pins and connect the SN pin to D pins as shown in Figure 24. Use 1oz of copper or thicker if possible to reduce trace resistance and reduce power dissipation. The VC bypass capacitor should be located as close as possible to the VC and GND pins. Place the PI2121 and bypass capacitor on the same layer of the board. The VC pin and CVC (shown as C2 in Figure 24) PCB trace should not contain any vias or connect to the ground plane close to the GND pin. Keep the power source very close to the S input pins, any parasitic in the trace connecting the power source and S pins will have inductive kick back when there is high current flow in the trace and the MOSFET turns off due to reverse current fault conditions. The inductive kick back Figure 24: PI2121 layout recommendation will produce a high voltage across the MOSFET. If it is not possible to connect the power source and S pins with a very short trace or common point, connect a capacitor (shown as C5 in figure 24), recommended value 1F, close to the S pins and return (ground). Also for the same reason use C7 in figure 24 at the output.
* *
*
*
Figure 25: PI2121 Mounted on PI2121-EVAL1 Please visit www.picorpower.com for information on PI2121-EVAL1
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 19 of 21
Package Drawing
Thermal Resistance Ratings Parameter Junction-to-Ambient (3) Junction-to-PCB Symbol
JA JC
Typical 54 14
Max -
Unit C/W C/W
Note 3: Thermal resistance characterized on PI2121-EVAL1 evaluation board with 0 LFM airflow. Ordering Information Part Number PI2121-00-LGIZ Package 5x7mm 17-pin LGA Transport Media Tape & Reel
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 20 of 21
Warranty
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor shall not be liable for collateral or consequential damage. This warranty is extended to the original purchaser only. EXCEPT FOR THE FOREGOING EXPRESS WARRANTY, VICOR MAKES NO WARRANTY, EXPRESS OR LIMITED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Vicor will repair or replace defective products in accordance with its own best judgment. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty. Information published by Vicor has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Vicor reserves the right to make changes to any products without further notice to improve reliability, function, or design. Vicor does not assume any liability arising out of the application or use of any product or circuit; neither does it convey any license under its patent rights nor the rights of others. Vicor general policy does not recommend the use of its components in life support applications wherein a failure or malfunction may directly threaten life or injury. Per Vicor Terms and Conditions of Sale, the user of Vicor components in life support applications assumes all risks of such use and indemnifies Vicor against all damages.
Vicor's comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor's Terms and Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Vicor Corporation 25 Frontage Road Andover, MA 01810 USA
Picor Corporation 51 Industrial Drive North Smithfield, RI 02896 USA
Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com Tel: 800-735-6200 Fax: 978-475-6715
Picor Corporation * picorpower.com
PI2121
Rev. 1.0
Page 21 of 21

▲Up To Search▲

Price & Availability of PI2121

	To Download PI2121 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .